Heart Wristlet

Super Cute heart wristlet!
Things you will need
main fabric – Arrow fabric
lining fabric – chevron
zipper that spands the width of your heart – zipper
a metal loop, key finding, jewelry finding to attach the wrist strap – D ring
fusible fleece – http://go.magik.ly/ml/3od5/
Slice two of the piece of fabric in half as shown , this is where zipper will be placed

 cut and iron fusible fleece to fit the heart 1/4″ smaller (this will help reduce the bulk in the edges of the heart

 Using a hot iron press both sides, if you dont have fusible fleece a stabilizer material  will work as well

 place the top of the heart (main fabric) on your table right side facing up, place the zipper zipper side down onto the piece of fabric lining up the edges of the zipper with the bottom part of the heart piece, place the lining fabric ontop of the zipper right sides facing down. sew along the that edge as close to the zipper as you can get, if you have a zipper foot that would be the best option.

if you have difficulties placing the fabric please refer to my video tutorial linked below

once you finished sewing the zipper on fold the two pieces of fabric back to expose the zipper and sew along the edge near the zipper about a 1/4″ away for a nice top stitch

 now we will attach the bottom of the heart, laying down the main fabric and then the zipper portion (zipper down) and then lining right sides down, making sure the edges of the fabric all line up and the bottom of the hear lines up with the top of the heart on the sides. sew next to the zipper, sometimes its hard to get past the zip so if you sew a small portion of it and then take the piece of out of your machine to move the zip then you can get past it better.

flip open the fabric to expose the zipper and again top stitch 1/4″ away from the zipper
Note the zipperfoot is very handy and can butt up to the zipper
Now its time to attach the back of the heart!
keeping the sewn portion facing up, lay the main fabric heart down onto the sewn portion right sides down, then lay the lining fabric on top with the right side facing up.
slip in the loop on the right hand corner of the heart and pin in place.
Sew all around the perimeter of the heart, once you have passed over the zipper (slowly) open it up half way and then continue on sewing the entire thing
once finished flip it right sides out
 it takes a minute or two and a little bit of finessing but it should look like this!
now for some top stitching 

very slow and steady when you go over your zipper! if its metal zip over the teeth!
and then your done! just in time for your valentines day dinner 😀 how adorable and it will fit a samsung s7 some money and a few small makeup items so thats a plus!

Half Moon Zipper Toiletry, make up or essential oil pouch

For this tutorial you will need Cotton Fabric, a Outer fabric and lining fabric

12″ or more length zipper

Fusible Fleece or Light to medium weight fusible interfacing

you will need 6″ bias tape, if you don’t have bias tape you can take the fabric the lining is made out of and create  your own bias tape

Get the pattern here!

Paid patterns are to help support my youtube channel and to help buy materials to bring you more and quality content, so Thank you! 😀

find the centre of your zipper and fold the fabric in half length ways to find the centre of the half circle, line up the middle of each and start to pin your zipper along  the edge, using a zipper foot will make this process easier Sew along the side of the zipper, next you will put the lining ontop and again sew along the same edge to attach the lining (make sure the lining and the main fabric is right sides together with the zipper sandwich in between

** You can of course sandwich the zipper between the main fabric and the lining all at once but it can be a little tricky sewing a zipper onto a curved edge so nothing wrong with doing it one step at a time if you are a beginner

This is how it will look once you have sew on the lining, now we will upzip the zipper and do the same thing on the other side, making sure the zipper isnt twisted and lining up with the edge of the main fabric and lining

no shame in using 1000 pins or clips haha

This is how it will look once you have done both sides, it will look puckered at the side where the zipper is attached but thats ok

Now you will flip it right sides out from one of the cut notches

Now you will do a top stitch next to the zipper to finish it off the zipper

Free Shipping on Orders $49+

*Use a long stitch length to make it a little more fancy and try to go as straight as you possible can

turn the bag inside out and pinch the notches lining up the zipper with the centre of the notch, clip into place and sew along that edge

add bias tape to finish it off

Turn right sides out and then your done!

Lace Zipper Square Pouch tutorial

Things you will need

Cotton Fabric a lining and an outer fabric

For this tutorial i chose this unicorn print and a plain lining, this print is from Joann Fabrics

I also used medium OR light weight interfacing, the interfacing will add structure to the bag as the cotton is too flimsy and will lay flat otherwise

i used Grosgrain ribbon for the ribbon accents on the sides of the bag

Fabric – 8″x12″ 2 in main fabric, 2 in lining fabric

Zipper – 8-9″ in length

Interfacing Cut 2 at 8 x 12″

**FINISHED PRODUCT MEASURES 5 1/2″ X 5 1/2″ X 2 1/2″ tall

My Fabric is direction so i will be placing the fabric in the opposite ways so that it appears right side up on the bag

First take main fabric and lining fabric and place right sides together, do this for the other two pieces

Sew along the one side (8″ side) at the top of your fabric if its direction

flip right sides out and press that seam

do that for the other side

you will then sew this zipper on top, do one side at a time placing the zipper along the edge of the sew side of your fabric, make sure your fabric doesnt get too close to the teeth of the zipper on the underside so it doesn’t end up catching in the teeth once the bag is complete

use a matching thread so it will be invisible to the naked eye, in my machine i put a pink thread on the top of my machine and kept a white thread on my bobbin, the pink will be on top and the white will be underneath

once you are done sewing on y our zipper put ride sides together, main fabric right sides together with itself and the lining right sides together

we will be sewing down each side, in this photo i will be sewing the left side and the right side

Once done you will be able to unzip your zipper and open it up and put it right sides out, but then we will put it inside out and flatten it like shown, make sure the zipper and the bottom seam are lined up

we will then insert our 2″ piece of ribbon, you might need to unzip your zipper to get the pull out of the way, use pins or clips to keep it all together as it can be tricky to hole it all in place

fold the  ribbon in half and insert between the seam and the zipper, make sure the raw edges of the ribbon are lined up with the raw edges of the bag, sew along each side of your bag

**the raw edges will be exposed and that is fine at this point

Now we will cut notches into all 4 sides of the bag, i measured a 1 1/4″ by 1 1/4″ square and cut it out, the depth of your bag is depending on this measurement

my bag is 2 1/2″ high, whatever your measurement of  your square is multiply that by 2 and that will be the height of your bag

After you cut your notches you will grab some bias tape or 1 to 1 1/2″ ribbon and cover up those raw edges, you will do this again with the next step so keep that bias tape handy

After you are done covering the sides with bias take u will then flatten each of your cuts taking the side seams and lining it up with the middle of that cut, basically take your cut open it and squish it the opposite way, line up all the fabric making sure your lining and main body fabric is all lined up together

Do this for all 4 sides, once you have sewn all 4 sides, and covered with bias tape you will carefully undo the zipper providing you gave yourself some room to access it hahah! flip it right sides out and poke the corners and your done!